Installing A Bath tub
Installing A Bath tub
Blog Article
What are your opinions regarding Installing A Bathtub?
Mounting a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably hard project. If the old bathtub is conveniently easily accessible, the project can move immediately; if you need to open a wall surface to get rid of the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have actually qualified yourself for the task and also fit attempting it. Instead of working with a contractor to take over a halfway-completed job, it is better to consider using one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This short article will aid you mount a brand-new bathtub in your restroom if you have actually currently bought a new tub and do not need to change the plan of your previous water system pipelines.
Your tools as well as product list must comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing faucets can be fairly troublesome because of the restricted gain access to that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a fabric prepared for the staying water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin making sure that the washers are in location in between the tap and also the sink. Secure the faucet in place with the supplier supplied backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small points.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bath tub until the spirit level checks out level.
To set up faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water and examine all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill the tub and likewise check the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as described in the manufacturer's user's manual. Tiling and securing around the tub needs to wait till the bath tub has been utilized a minimum of when as this will certainly settle it into its last placement.
Planning for the Installment
First of all, the sustaining framework supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom and the tiling, leading to problems with wetness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the tub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the market. It is recommended to fit the ceramic tiles using water-resistant or water-proof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about A Step-by-Step Guide to Installing a Bathtub? Place a remark further down. We would be delighted to know your thinking about this write-up. We hope to see you back again soon. Don't hesitate to set aside a second to promote this post if you enjoyed it. Thanks for taking the time to read it.
Book A Service Call
Report this page